Products

Crosswalk Pedestrian Pedestal and Signal Poles

Crosswalk Pedestal and Signal Poles

Our pedestal base features a slim design with only a 7" footprint allowing for ADA accessibility to your crosswalk button. The base is also easy to install and replace in the event of a knock down. AASHTO MASH FHA tested.

Click here for more details!

Saddle Adapter

The Saddle Adapters have been developed to aid in the ability to extend an APS switch. This will allow your button to become ADA accessible.

Click here for more details!

22PMAG Pole Mounting Adapter Galvanized

For mounting pedestrian audible or non-audible crosswalk switch on a pole where a sidewalk has no room for a crosswalk pedestal. For new construction or retrofit. Round surface to aim switch button arrow at the crosswalk for the blind or disabled.

Click here for more details!
      We have our AASHTO MASH testing passed and approved, and our FHWA letters of eligibility so the city can receive 80 to 90% Federal aid when using our Crosswalk pedestals and signal poles on upgrades and new construction on Federally approved State, County, and City projects. Below are the links related to the testing and Federal aid program:
      FHWA Website Six minute “Introduction To Federal-Aid” video:
          https://www.fhwa.dot.gov/federal-aidessentials/catmod.cfm?id=44

      AASHTO MASH Frey Manufacturing Corp. equipment Test Video:
          https://www.youtube.com/watch?v=ap2xXilwRc4

      AASHTO MASH Breakaway Implementation Frey Manufacturing Corp. presentation:
          https://www.beautiful.ai/deck/-LZ_Q9O9oLZArsCtXy8Y/Untitled

      Status by state of FHWA/AASHTO MASH Breakaway Implementation: (click on your state for status)
          https://safety.fhwa.dot.gov/roadway_dept/countermeasures/reduce_crash_severity/results_by_state.cfm

      Federal-Aid Coordinators by state: (click on your state)
          https://www.fhwa.dot.gov/federal-aidessentials/stateresources.cfm

We have been speaking at several IMSA, TEAM, ITE etc. conferences, and County, City, State DOT’s, and consulting with AASHTO members and representatives about this program. It is our understanding that care should be taken to not mix tested mounting equipment with untested mounting equipment (may not apply to the devices attached to it). Our equipment has been AASHTO MASH tested - bases, pipes 4’ to 15’ length Schedule 40 and Schedule 80, caps, cable tether (Drawing attached) to provide a complete approved FHWA pedestal and signal mounting pole eligible for the Federal-Aid. AASHTO MASH Test reports and FHWA letters are available upon request to DOT offices.

Signal Mounting

35E Elevator Plumbizer

The 35E plumbizer is designed for signal mounting mid-mast arm, end of mast arm or on the pole. It uses a ball and socket mounting point for easy leveling adjustment to ensure your signals are plumb and level. Mounting the signal heads is easy with just a washer and locking nut. The plumbizer is bolted tightly and does not use set screws for adjustment making it almost maintenance free. Pedestrian signals can also be mounted to the 35E which will allow the traffic signals and pedestrian heads to be aligned with each other on the pole while maintaining the ability to aim the signals in the appropriate directions. Also see 11PC Pedestrian Cap (Dwg. 9.1.0).

Click here for more details!

45V Angle Mount Plumbizer

The 45V plumbizer is designed for signal mounting end of mast arm or on the pole. It uses the same ball and socket mounting as the 35E for easy leveling adjustment to ensure your signals are plumb and level. Mounting the signal heads is easy with just a washer and locking nut. The plumbizer is bolted tightly and does not use set screws for adjustment making it almost maintenance free. Pedestrian signals can also be mounted to the 45V which will allow the traffic signals and pedestrian heads to be aligned with each other on the pole while maintaining the ability to aim the signals in the appropriate directions

Click here for more details!

15PC Pedestrian Cap

The 15PC is used on the 35E and 45V for capping off the top side of the plumbizer when mounting a pedestrian signal to the bottom side. The sap is designed to bottom out on the threads before damaging the teeth on the plumbizer so it can be used for a different application in the future.

Click here for more details!

35EA Open End Elevator Plumizer

We have developed the 35EA Open End Elevator Plumbizer for use with the McCain programmable, and other manufacturer’s signals. The 2” hole in the mounting point provides the proper room for wiring and mounting bolts that are required to mount this signal to the plumbizer. As with the 35E, this plumbizer provides the same ball and socket mounting to the flange on your pole or mast arm. This plumbizer also mount to our adapters. Various accessories are also available for this plumbizer such as the Sealed Cap and LPK mounting kit for regular signals.

Click here for more details!

45VA Open End Angle Mount Plumbizer

We have developed the 45VA Open End Angle Plumbizer for use with the McCain programmable, and other manufacturer’s signals. The 2” hole in the mounting point provides the proper room for wiring and mounting bolts that are required to mount this signal to the plumbizer. As with the 45V, this plumbizer provides the same ball and socket mounting to the flange on your pole or mast arm. This plumbizer also mount to our adapters. Various accessories are also available for this plumbizer such as the Sealed Cap and LPK mounting kit for regular signals.

Click here for more details!

52CA Cluster Adapter

The 52CA is an adapter for the 35E or 45V plumbizer to configure a “dog house” arrangement. It can be used in the normal configuration or inverted. It is also ready to accept a blue light.

Click here for more details!

32B Two-way Plumbizer

The 32B plumbizer is designed for mounting two signals on the same mounting point. It can be mounted mid-mast arm, end of mast arm or on the pole. It uses tapered washers for a leveling adjustment to ensure your signals are plumb and level. The plumbizer is bolted tightly and does not use set screws for adjustment making it maintenance free. Pedestrian signals can also be mounted to the 32B which will allow the traffic signals and pedestrian heads to be aligned with each other on the pole while maintaining the ability to aim the signals in the appropriate directions.

Click here for more details!

CAP - Sealed Cap

The CAP is used on the 32A, 32B, 35VA, and 45VA plumbizers for capping off the top side of the plumbizer when mounting a pedestrian or single signal to the plumbizer.

Click here for more details!

11F Spacer (32F2 or 32F4)

The 11F spacer is used on 4 and 5 section signal heads to relieve stress off the heads by making 3 point mounting. This will allow to get the full life out of your signals without warping over time. 2 castings must be ordered for each signal.

Click here for more details!

Mast Arm Extension - Clamp or Strap on (For Signal Extention)

The mast arm extension is a great money saver. This piece of equipment is used for extending your signal out from the end of your mast arm up to 5 feet. For instance if you add a turn lane to your intersection and a new mast arm is not in the budget, the signal can still be lined up with the lane by extending out 5 feet.

Click here for more details!

Mini Mast Arm - Clamp or Strap on (For Signal Extention)

The Mini Arm Extension is ideal for adding a signal where there is a pre existing pole. It simply straps on to a pole and extends your signal out up to 5 feet. This is a cost effective and extremely easy way of adding a signal to your intersection.

Click here for more details!

Mast Arm Damper

The damper mount is a device used for dampening the harmonics of a mast arm caused by wind. It is intended for use on longer mast arms to reduce or eliminate harmonic bouncing caused by the wind, but it can also be used to steady shorter mast arms that have cameras or other sensitive equipment. The federal government is requiring that harmonics on mast arms 55 feet and longer must be addressed. Our damper mount complies with this requirement. Instructions for installing our mast arm damper are supplied with every order and must be followed for proper placement to allow proper airflow.

Click here for more details!

Adapters

45B Threaded Hub

The 45B is for adapting a plumbizer to a mast arm pole by using an 1 1/2 “ nipple threaded into the pole. It make for a very clean look on the mast arm pole without the use of pipes holding signals. When using the 52CA cluster adapter the 45B Extended must be used to allow enough clearance for rotational adjustment. The 45B Extended uses a 3” nipple for the extra clearance.

Click here for more details!

32UB Universal Bolted Hub
For schedule 40 or 80 pipe

The 32UB is designed is for adapting a plumbizer to a mast arm or pedestrian pole by bolting to a surface where there is not a welded 1 ½” threaded hub to accept the 45B. It is attach by easily by drilling two holes into the pole and crimping in two insert nuts. There is no need to drill and tap when using the supplied insert nuts. A removable template is also provided for quick installation. The 32UB can be ordered for a schedule 40 or schedule 80 pipe.

Click here for more details!

32D Strap Adapter

The 32D is designed is for adapting a plumbizer to a mast arm or pedestrian pole by bolting to a surface where there is not a welded 1 ½” threaded hub to accept the 45B. It is attached with two straps 1 1/2” wide and come 40” long for field cutting to the appropriate length. The straps also have holes for a grounding bolt to be drilled and tapped to maintain the NEC ground. (Strapping to a painted surface is not an NEC ground)

Click here for more details!

32DR Through Bolt Adapter

The 32UB is designed is for adapting a plumbizer to a mast arm or pedestrian pole by bolting to a surface where there is not a welded 1 ½” threaded hub to accept the 45B. It is attached by drilling through a pole and using a threaded rod with an acorn nut on the opposite side. Also two 11D castings can be used back to back on the same pole using the same threaded rod.

Click here for more details!

32C Clamp Adapter

The 32C clamp adapter is used for clamping on to a 2" tenon and creating a flange with the correct bolt pattern for the plumbizer. It is also used in other various equipment FMC offers.

Click here for more details!

32DF40 Flat Strap Adapter Adapter

Used for Damper, Mini-Arm Signal Bracket, Strap-on Mast Arm Extension, and sign mounting.

Click here for more details!

Accessories

KBR Series (3/4" or 1" Pipe Thread Hub and AOB)

KBR ¾” Pipe Thread Hub, and KBR1 1” Pipe Thread Hub for EVP, camera and AOB mounting.

Click here for more details!

LPK (Parts Kit)

LPK parts kit is for attaching non-programmable signals to the 32B Two-way, 35EA straight, and 45VA angle plumbizers.

Click here for more details!